u/newbie-ender5pro · 2023-03-21 14:43:20 UTC · score 1
It gotta be something simple... Possibly even your take down spring is too tight... Like pushing up too much
u/BrilliantPossible8 · 2023-03-21 14:44:53 UTC · score 1
you see how it gets stuck when going in motion to chamber? could my slide lock spring be messed up?
u/newbie-ender5pro · 2023-03-21 16:36:38 UTC · score 1
I've had a ghost connector that never worked. But the more I think about it, it's more likely your take down spring is pushing up too much pressure. Probably adjusted it. If that doesn't work I'll send you a picture...
u/newbie-ender5pro · 2023-03-21 14:40:16 UTC · score 1
It may... There's definitely videos you can watch to figure out what's catching. I'll look and add it here in a minute.
u/BrilliantPossible8 · 2023-03-21 14:29:16 UTC · score 1
so the trigger bar could be snagging on the slide?
u/BrilliantPossible8 · 2023-03-21 14:33:10 UTC · score 1
trigger connector is ghost one and it’s perfect
Originally posted by u/sandshark- at 2025-06-30T23:40:04Z
Hello! If youre reading this and have a FMK 91C please hit me up. I need some reference photos of the frame. Kits for these are pretty cheap and I'd like to hop on Fusion and get one designed and printed. Please feel free to message me if you have one. TIA
Source: https://i.redd.it/53z6a6y8h5af1.jpeg
Source: https://b.thumbs.redditmedia.com/EBlIwJ2BDSqFWmLRh23mV5qGIhmf0yZHt8dYodxtqDM.jpg
Originally posted by u/No_Swordfish7008 at 2025-06-30T23:36:25Z
Source: https://a.thumbs.redditmedia.com/oIYyIX6iOzo3gE4DoJ_DHaVkNwWTCjb0IfGdJZ8wvH8.jpg
Originally posted by u/MrFartyStink at 2025-06-30T23:31:39Z
Iv printed the scarab v2 totally fine but this keeps either disconnecting from the supports at the front or rear. Polymaker pla pro 220/65 80mm/s top z distance .26. I have it orientated at a 45° like the scarab v2 but this has less surface area with the build plate than the scarab v2. How did yall print it/ orient it?
Originally posted by u/Ok-Blood8662 at 2025-06-30T21:50:55Z
Was hoping I got good enough layer adhesion here, and I may have, but cracks formed at the pin holes.
Fortunately did not have this happen while firing. I noticed the cracks when inspecting the gun at my desk, flexed it, and it completely snapped.
Figured I would share as an example to others. Filament choice is super important in 3D2A. Be careful.
Source: https://i.redd.it/cm8nb5w9y4af1.jpeg
Source: https://b.thumbs.redditmedia.com/Hvop_ukpbveaGUcW1rK6eqQQ2dwiHHpLgQBXvciEnEw.jpg
Originally posted by u/BiggOskee at 2025-06-30T20:54:40Z
Been sitting on this for a while. Finally got my Foxtrot Mike build kit. Rosco 14.5" barrel, just waiting for gas block, bolt and muzzle device.
view more: next ›
u/newbie-ender5pro · 2023-03-21 14:51:29 UTC · score 1
It could need to be a little less spring.